Laying ceramic tiles on large-format bricks
![](https://molins-dev.mo2o.com/construction-solutions/wp-content/uploads/sites/6/2021/12/miniatura-0041-miniatura-colocacion-ceramica-ladrillo-de-gran-formato-1.jpeg)
Civil work
Edification
SoluciónLaying ceramic tiles on large-format bricks
Descripción sistema
Large-format partition systems are a construction solution that allows partition walls to be built quickly, with a minimum number of joints and a high level of finished flatness.
![](https://molins-dev.mo2o.com/wp-content/uploads/sites/6/pc_block_prop/4266/value/propamsa-0007-cuadrada-regle-ok.jpg)
The good planimetry characteristic of this type of partition wall makes it possible to tile directly into it.
![](https://molins-dev.mo2o.com/wp-content/uploads/sites/6/pc_block_prop/4329/value/propamsa-0003-soporte-prefabricado-16bded-ok.jpg)
The water absorption of large format bricks and the plaster-based adhesive used for their installation determine the choice of a suitable adhesive mortar.
For correct installation, it is necessary to use a glue mortar that guarantees optimum adhesion without sagging, PAM® ECOGEL PORCEL.
Linked solutions
- INSTALLATION OF LARGE-FORMAT CERAMIC TILES ON FLOORS
- LAYING OF CERAMIC TILES ON OUTDOOR TERRACE
- CERAMIC TILE INSTALLATION ON FRESH MORTAR
- LAYING TILES ON PREFABRICATED GYPSUM BLOCKS
- LAYING OF CERAMIC TILES ON FAÇADES
- CERAMIC TILE INSTALLATION ON IRREGULARLY SHAPED SUBSTRATES
- LAYING CERAMIC TILES IN SWIMMING POOLS
- CERAMIC TILE INSTALLATION ON PLASTERBOARD SUBSTRATES
- LAYING TILES ON FLOORS WITH UNDERFLOOR HEATING
- LAYING OF PORCELAIN STONEWARE
- INSTALLATION OF NATURAL OR ARTIFICIAL STONE ON FAÇADES
- LAYING A TILING ON TOP OF AN OLD ONE
- LAYING CERAMIC FLOORING ON TOP OF AN OLD ONE
Related products
Solution
PREPARATION OF THE SUBSTRATE
![](https://molins-dev.mo2o.com/wp-content/uploads/sites/6/pc_block_prop/10244/value/cepillo1-ok.jpg)
Brush or wipe the surface of the large bricks with a damp sponge to remove dust and dirt from the brickwork.
![](https://molins-dev.mo2o.com/wp-content/uploads/sites/6/pc_block_prop/10253/value/obra-014-ok.jpg)
Apply PROPAM® DUR to the substrate, when the partition is excessively coated with plaster glue residues.
APPLICATION
![](https://molins-dev.mo2o.com/wp-content/uploads/sites/6/pc_block_prop/4296/value/propamsa-0010-aplicando-cemento-cola-ok.jpg)
Spread PAM® ECOGEL PORCELon the substrate with a notched trowel and check that the open time of the adhesive has not expired.
![](https://molins-dev.mo2o.com/wp-content/uploads/sites/6/pc_block_prop/4303/value/propamsa-0008-colocacion-piezas-ok.jpg)
Place the pieces, exerting good pressure on them, until the grooves are completely flattened.
![](https://molins-dev.mo2o.com/wp-content/uploads/sites/6/pc_block_prop/4310/value/propamsa-0004-rejuntado1-ok.jpg)
Leave a minimum joint width of 2 mm and grout after 24 hours with the BORADA®range of joint mortars byMolins.
Recommendations
- Use the double gluing technique when the tile format is greater than 900 cm² and always when the difference in planimetry is greater than 10 mm.
- VAT® SUPER, VAT® EXTRA can be used if the pieces are smaller than 30 cm on a side.
- For laying large tiles >90 cm from one side, use PAM® ECOGEL FLEX.